Standard product range for shot blasting/ light peening purpose with quenched and hardened. It is a spherical product of hypereutectoid steel having Carbon more than 0.85%. We offer superior specification from the industry level in terms of controlled sizing & hardness, higher % of Mn available so that product will be more wear resistant. Most of the industries uses this product for all their shot blasting & peening applications where desired effect for mass and maximum rebounding effect require.

Size Distribution:

Chemical Composition:

• Density: 7.4 gm/cc
• Microstructure: Tempered Martensite
• Standard Hardness: 46~51 HRC
• Special Hardness: 53~57 HRC & 60 HRC+
• Durability: 2800~3000 cycles

---

Cast Steel Grit is produced by crushing of specific sizes of steel shot. Two out of three product range is heat treated. It is utilized for blast cleaning as well as surface preparation job by the industry.

GP STEEL GRIT

Quenched & tempered product, used in wheel blast machine for the faster cleaning of product. Product has same hardness of Steel Shot which is 46~51 HRC. Initially shape is angular & during operation shape changes to round. Suitable for Desanding / descaling applications.

GL STEEL GRIT

Quenched & tempered product, used by wheel blast machine for achieving specific roughness on product. Product has moderate hardness 53~57 HRC. Best suitable for blasting on rubber molded product. Like GP this product shape also angular initially however during operation it changes to multi point contact shape. Best suitable for surface preparation industry.

GH STEEL GRIT

This is product is untampered, has highest hardness >60 HRC. Recommended to use only in Air Blasting Machines or Stone Cutting applications. Product shape always use to be angular. During operation particles break & form smaller size with angular only. This product is particularly effective in surface treatment and produce a uniform, etched finish.

Size Distribution:

Chemical Composition:

• Density: 7.6 gm/cc
• Microstructure: Tempered Martensite
• Hardness: GP - 47~52 HRC, GL – 53~57 HRC, GH – 60 HRC+
• Durability: GP – 2600~2900 cycles, GL – 2000~2500 cycles, GH – 1200~1500 cycles

---

Manufacture from High Quality Solid Wire. The product gives maximum life & highest impact during the operation. Recommended to use to remove highest sticky foreign particles (Infused sand in foundries or scale in forgings) from the product.

HIGH CARBON CUT WIRE SHOT POLISHED

Solid product with the highest aggressiveness in nature, made from the high quality wire. The new particles are in cylindrical shape. Generally used by the foundry customers. The product gives maximum energy transfer for the cleaning purpose & gives the highest life.

HIGH CARBON CUT WIRE SHOT CONDIITONED

Like Polished cut wire shot this product is also solid product with moderate aggressiveness. Produced by conditioning of polished shot to remove edges. Highly recommended to use in Wheel blasting machines for Foundries & Forging Industries. This product gives highest return to customer among the all available products in market.

Size Distribution:

Chemical Composition:

• Density: 7.8 gm/cc
• Microstructure: Tempered Martensite
• Hardness: 40~51 HRC
• Durability: Polished – 3200~3400 cycles, Conditioned – 3000~3200 cycles

---

Stainless Steel Shot is the ideal solution for blasting stainless steel and non-ferrous metals. This product range has two category High Chrome and High Chrome with High Nickel.

HIGH CHROME (C)

High Chrome "C" is the ideal product for blasting stainless steel and non-ferrous part and especially when more cleaning efficiency required.

This product is use to blast Non-Ferrous parts when light rusting can be accepted after blasting or some plating use to be done later on. Chrome % is ~15%

HIGH CHROME HIGH NICKEL (CN)

CN is used in all applications where non-rusting materials such as aluminum, zinc, stainless steel, brass, bronze, etc. are blasted.

CN is large spectrum of grain sizes makes it perfect for cleaning, de-burring and surface finishing of all types of castings, forgings, profiles, wire and welded structural parts, without the possibility that rust could discolor the bright surface due to ferritic dust.

CN distinguishes itself by having a high percentage of spherical grains and by its compactness. The end result is low consumption, high performance and low machine wear. Using CN on smooth and textured pavers brings out the stones unique appearance, and the possibility of developing unsightly rust spots on the surface of blasted concrete and granite stones due to the remains of ferritic particles is ruled out.

Product is use to blast Non-Ferrous parts especially when NO RUSTING is required after blasting on component. Chrome % is ~ 15% & Nickel % is ~10%.

Size Distribution:

Chemical Composition:

• Hardness: C Grade - ~41 HRC, CN Grade - ~ 30 HRC
• Microstructure: C Grade – Austenitic/ Ferritic, CN Grade - ~ Austenitic